Resin embedded magnets

I gave paper embedding another go, and I’m pleased I did! This time I used Modge Podge to seal the paper and Entropy Super Sap CCR Resin in a silicone mould!

 embedding paper in resin 
First step was to cut the circles to be embedded. I used a circle cut from wax paper to use as a guide of where to cut.

Then each piece was laid out on wax paper and coated twice with Modge Podge, before pealing off, flipping over and laying out on a fresh piece of wax paper to be painted with the Modge Podge again….. And again….

 embedding paper in resin  
embedding paper in resin  embedding paper in resin 
Next each circle is pedalled off and trimmed, preferably leaving a small edge of dried M.P.

 embedding paper in resin 
Now for the embedding!

I greased the silicone mould by wiping it down with some spray oil. Then filled the cavities with about 5mm of the Fibreglass Shop’s Entropy Super Sap CCR Resin, and let cure. 

 embedding paper in resin  
embedding paper in resin 
Then I poured another 5mm of resin and embedded the pieces of paper, being careful not to trap air bubbles. 

 embedding paper in resin 
The following day the pieces were cured and could be removed from the mould.

I’m super happy with the results and will glue some magnets to the back with Clear Liquid Nails! 

 embedding paper in resinThere were a few marks where the paper wasn’t completely sealed by the Modge Podge, and the resin has seeped thru, but not a major ; ) (maybe 3 coats next time)

 embedding paper in resin https://www.fibreglassshop.co.nz

Advertisements

Sandy resin bowl

Finished this cutie today!

I really love the look of sand in resin so will definitely be making more!

I used some empty containers as a mould. Cut the base off the larger bowl so that I could pour in the resin. I used silicone to stick the bowls to the ice cream lid base. 

Rookie mistake was to leave the label on the smaller bowl. This got stuck to the resin and needed sanding off once cured. 

The sand had been washed and left in the sun to dry before use. 

The resin I used was from the Fibreglass Shop. Ordered online and delivered the following day! Awesome service. (Would be nice if the safety infomation and instructions were included with the epoxy and it’s hardener, instead of having to print it off online myself.) 

I use Entropy Super Sap CCR Epoxy Resin. It’s easy to mix and quick to harden, and doesn’t  have the nasty smell that polyester resins have. 

http://www.fibreglassshop.co.nz/search?q=Ccr

 resin bowl  
 resin bowl mold mould 
  resin bowl   
resin bowl 
Not sure what it is worth so have popped it for sale on Trade Me ; )

https://touch.trademe.co.nz/listing/view/1026628089

Epoxy experience

So I was recommended an epoxy resin to use, and to be honest, two pots of Kleer Kast Polyester Resin and I’m over it. It smells soooo bad, takes ages to fully cure, and often leaves a tacky surface which needs doming or sanding to eliminate.

So I purchased 1.5L of Entropy Super Sap CCR (Clear Cast Resin) from the Fibreglass Shop in Hamilton.

http://www.fibreglassshop.co.nz/search?q=Ccr

It was so easy to mix, a 1:2 ratio to a hardener, and didn’t smell!!!!


I ordered a silicone soap mould, and had a go embedding insects and a fern that I had been drying out.

I wiped down the mould with spray cooking oil, then half filled each space with resin. After curing for 30min I placed the pieces and left over night.


 The following day I filled the spaces, covering the pieces to be embedded, and left the mould under a dome to fully cure.

It was a hot day and by the afternoon they were fully cured, with no tacky surface!!!!

I messed up tho and had quite a few boo boos.

The insects had continued to bubble. I should have stayed and watched it cured for a while ensuring all bubbles were expelled.

Even the fern was crappy. I should have pressed it firmly into place to push the bubbles out.

Oppsie. Oh well, heaps of fun playing in my shed ; ) will try again tomorrow.

Loving Fibreglass Shop’s  Entropy Super Sap CCR (Clear Cast Resin). Purchased online via their website and couriered to my doorstep the very next day.

  
  
  
  
  
  

Making a silicone mould

This was a really fun project. I love using silicone to make moulds. I started making my moulds with liquid latex, which is very time consuming and the result is a much more flimsy less durable mould. I purchase my liquid latex and silicone from www.stmpro.co.nzsilicon silicone mould mold for resin bracelet

I found this basic wooden bracelet at our local op shop, purchased for $1. I pressed pins into one side of the bracelet and trimmed them to approx. 5mm long. This created a kinda of tripod that the bracelet could stand on, so that the silicone would surround the entire bracelet, leaving a couple of tiny knobs to sand off at the edge, rather than a complete blunt edge to round.

silicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletI placed the bracelet inside a plastic container, and blue tacked a small bottle to the centre. I lightly sprayed it with cooking oil to aid in mould release.

 

 

Then I got ready to mix the silicone.

STM Pro provides very clear instructions with their product, outlining all the safety precautions necessary and the correct ratios of silicone to catalyst.

 

silicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletsilicon silicone mould mold for resin braceletsilicon silicone mould mold for resin bracelet

Very happy with the end result, and look forward to producing some unique bracelets using Super Sap Clear Casting Epoxy Resin purchased online from http://www.fibreglassshop.co.nz